Loading... Please wait...

Erecaid EZ Ring

Hover over image to zoom

  • Image 1
  • Image 2
  • Image 3
  • Image 4
Osbon Erecaid
0.01 LBS
Calculated at checkout

 Product Description

Erecaid EZ Ring

The unique and patented design of the EZ Ring, which fits on the end of the cylinder like a lid, ensures that the scrotal tissue is not drawn into the cylinder of the pump. This design gives many patients a more comfortable fit, provides a better seal between body and cylinder, and greater tension to assist in maintaining penile rigidity. Once an erection has been created, the ring is removed from the end of the cylinder and remains at the base of the erect penis. The EZ Ring minimizes the ring transfer process. For use with Esteem or Classic cylinders and systems. 


EZ TENSION RING - Instructions for Use
The EZ Tension Ring has a unique and patented 
design which allows it to easily fit directly onto the end 
of the cylinder like a lid. This creates a firm seal with the 
cylinder and with penile tissue which facilitates the 
vacuum process. This design also ensures that the 
scrotal tissue is not drawn into the cylinder when 
pumping. These advantages give many patients a 
more comfortable tension ring fit and more tension to 
assist in maintaining penile rigidity. Once an erection 
has been created, the ring is slipped off the end of the 
cylinder and remains at the base of the erect penis 
minimizing the ring transfer process. EZ Tension Rings 
are intended for use with Esteem®
and Classic cylinders and Vacuum Therapy Systems. 

Step 1 – Remove the gray insert from the end of the cylinder provided with your Vacuum Therapy 
System and place the EZ Tension Ring on end of the cylinder like a cap or a lid, as shown below. 

Note: DO NOT USE Ring Loader with EZ Tension Rings 

Step 2 – Apply lubricant to the surface around the center of the opening of 
the EZ Tension Ring as well as to the entire head of the penis. 

Step 3 – Place the head of the penis against the opening of the EZ Tension Ring, 
making certain that the Urethral Notch is on the bottom and the Removal Grips are on the sides. 

Step 4 – Operate the vacuum pump by squeezing the handle or pressing the power button on the 
pump handle. This will remove air from the cylinder and also draw the penis into the cylinder. 
Allow the penis to be drawn through the opening in the EZ Tension Ring into the cylinder until the 
Ring is positioned near the base of the penis. 

Step 5 – Pump slowly for several seconds. Slow down or stop if you feel discomfort. Pause to let 
the blood flow into your penis. Continue pumping until your penis becomes erect and lifts off the 
cylinder floor and is firm enough for intercourse. 

Step 6 – Press the green vacuum release button and pull the EZ Tension Ring off the cylinder, so 
that the Ring remains positioned at the base of your penis. 

CAUTION: Do not leave the Tension Ring on for longer than 30 minutes. Allow 60 minutes 
between uses. 

Step 7 – Remove the EZ Tension Ring after sexual activity by pulling the Removal Grips outward, 
away from the penis. Hold the grips in this position until the penis loses some firmness. Then 
slowly pull the ring forward and off your penis. Additional lubricant may be needed to aid in 

Step 8 – Wash EZ Tension Ring with warm soapy water, rinse and dry thoroughly for storage until 
next use.

 Product Reviews

  1. for smaller people only

    Posted by robert on 2nd Nov 2015

    using a size 7 , but gets uncomfortable quickly
    I wish they had a size 8!

You Recently Viewed...


What's News

  • PAL Band Penile Adjustable Loop

    The penile adjustable loop is versatile due to it's tension can be adjusted to …

  • Combination Therapy

    Many men get frustrated trying to find a ED treatment solution. Sometimes it …

  • Venous Leak

    The most difficult part of ED is venous leak. Many men prematurely lose there …


Copyright 2024 ReachMedical.com. All Rights Reserved.
 Sitemap | BigCommerce Premium Themes by PSDCenter

Click the button below to add the Erecaid EZ Ring to your wish list.